- 您现在的位置：买卖IC网 > Sheet目录1222 > ISL1208EVAL (Intersil)EVALUATION BOARD FOR ISL1208
Application Note 1176
USB connector (CN1). This connector is a standard USB
type B connector which goes to the USB port of a PC using a
USB type A-B cable.
LEDs
There are three surface-mounted LEDs on the board. LED2
and LED3 monitor the TX and RX functions of the serial port.
They should be observed to insure that communication is
taking place with the serial port. LED1 monitors the power
supply and will light when the +5V power is applied from the
USB cable.
ISL1208 Daughtercard - Functional Description
(see Figure 4)
The ISL1208 daughtercard contains the ISL1208 device,
crystal, decoupling capacitor, temp-sensor, and an LED
(D1), for monitoring the open drain output.
FIGURE 4. ISL1208 DAUGHTERCARD
POWER
Jumper JP1 connects to the V CC pin of the ISL1208 device
and must have a shunt in place for the device to function in
normal mode.
OPEN DRAIN OUTPUT
The open drain output of the ISL1208 is the IRQ-F OUT
signal. There is a jumper (JP2) which connects D1 when a
shunt is in place, and also enables hooking up an external
pullup resistor if it is desired to use the logic signal. The
pullup resistor should terminate to a voltage that is less than
or equal to V CC .
CRYSTAL
A standard 32.768kHz surface-mounted crystal is supplied
on the daughtercard. A through-hole device can only be
attached by surface mounting the leads after the surface
mount device is removed.
TEMPERATURE SENSOR
There is an LM76 temperature sensor on the board which
measures ambient temperature, digitizes it, and provides it
to the microcontroller when prompted. Mounting on the
daughtercard enables remote sensing of temperature should
the daughtercard be placed in a temp chamber and wired to
the motherboard.
MEASUREMENTS
The V CC supply current may be monitored by adding a
series ammeter to JP1. D1 provides visual indication of IRQ-
F OUT status, and at low frequencies it will indicate that F OUT
is enabled. At higher F OUT frequencies it is possible to
monitor the pin with an oscilloscope. This allows good
monitoring of the crystal frequency, up to 32kHz. It is
possible to probe the X2 oscillator output with a scope
5
probe, but this is not recommended as it alters the oscillator
frequency or possibly stop it momentarily due to introduction
of a transient. If it is absolutely necessary to monitor the
oscillator output, use a low-capacitance probe (<2pF) or an
active probe and note that the absolute frequency monitored
will be higher than that without the probe.
ISL1209 Daughtercard - Functional Description
(see Figure 5)
The ISL1209 daughtercard contains the ISL1209 device,
crystal, decoupling capacitor, temp-sensor, and an LED
(D1), for monitoring the open drain output, similar to the
ISL1208 daughtercard. In addition there is a microswitch,
S1, and a connection block, J3, for the event-detect function.
Also, another LED (D2) is available for event monitoring.
The main functions of this daughtercard are similar to the
ISL1208. The important differences are discussed here.
EVENT-DETECT SWITCH, S1
This is a normally CLOSED switch which is typically
connected to ground. A shunt should be installed on J3 from
the EVT to GND position for this purpose. Depressing the
switch with the event detection software enabled will cause
an event to be recorded.
EVENT-DETECT OUTPUT
The event-detect output is open-drain and can be connected
to LED D2 by placing a shunt on JP3. With this output
enabled, the LED will light when an event occurs.
EVENT CONNECTION BLOCK
J3 contains all signals needed to connect a remote event
generating circuit to the evaluation board. V CC , V BAT , the
EVIN device input (labeled EVI), Ground, and a high value
pulldown resistor are all brought to this block. The 6 th
AN1176.0
June 20, 2005
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
ISL21007-EVALZ
EVAL BOARD FOR ISL21007
ISL21032-EVALZ
EVAL BOARD FOR ISL21032
ISL21060-EVALZ
EVAL BOARD FOR ISL21060
ISL21080-EVALZ
EVAL BOARD FOR ISL21080
ISL2109012EV1Z
BOARD EVAL 1.25V VREF ISL21090
ISL21400USB-EVALZ
EVAL BOARD FOR ISL21400
ISL28210SOICEVAL1Z
EVAL BOARD FOR ISL28210 8SOIC
ISL28217SOICEVAL2Z
EVAL BAORD FOR ISL28217 8SOIC
相关代理商/技术参数
ISL1208IB8
功能描述:IC RTC/CALENDAR I2C 8-SOIC RoHS:否 类别:集成电路 (IC) >> 时钟/计时 - 实时时钟 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- 类型:时钟/日历 特点:警报器，闰年，SRAM 存储容量:- 时间格式:HH:MM:SS（12/24 小时） 数据格式:YY-MM-DD-dd 接口:SPI 电源电压:2 V ~ 5.5 V 电压 - 电源，电池:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WDFN 裸露焊盘 供应商设备封装:8-TDFN EP 包装:管件
ISL1208IB8-TK
功能描述:IC RTC/CALENDAR I2C 8-SOIC RoHS:否 类别:集成电路 (IC) >> 时钟/计时 - 实时时钟 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- 类型:时钟/日历 特点:警报器，闰年，SRAM 存储容量:- 时间格式:HH:MM:SS（12/24 小时） 数据格式:YY-MM-DD-dd 接口:SPI 电源电压:2 V ~ 5.5 V 电压 - 电源，电池:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WDFN 裸露焊盘 供应商设备封装:8-TDFN EP 包装:管件
ISL1208IB8Z
功能描述:实时时钟 I2C REAL TIME CLOCK/ CALENDAR 8LD RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube
ISL1208IB8ZR5291
功能描述:实时时钟 I2CAL TIME CLK/CLNDR ALL BATRY MODE TESTS RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube
ISL1208IB8Z-T7A
功能描述:实时时钟 I2CAL TIME CLK/CLNDR 8LD RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube
ISL1208IB8Z-TK
功能描述:实时时钟 I2C REAL TIME CLOCK/ CALENDAR 8LD RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube
ISL1208IB8Z-TKR5291
功能描述:实时时钟 I2CAL TIME CLK/CLNDR BATRY MODE TESTS RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube
ISL1208IRT8Z
功能描述:实时时钟 I2CAL TIME CLK/CLNDR 8LD 3X3 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube